You are currently browsing the archives for the Power Factor Conditioning Unit category.

Calendar

February 2012
M T W T F S S
« Dec    
 12345
6789101112
13141516171819
20212223242526
272829  

Archive for the ‘Power Factor Conditioning Unit’ Category

Fuel surcharge for high energy usage

Wednesday, October 28, 2009
posted by livinggreen

Most utility companies have a multi-tiered system for charging their residential customers. If your usage is very low, you pay the baseline rate. As your usage goes above the baseline, progressively highly rates apply. You might have noticed that when cold weather sets in, your electric bill suddenly doubles even though you might not have used that much more energy.  The diagram below shows the rate schedule for residential customers of PG&E. Notice a 56% increase in rate as usage goes above the baseline level by just 30%.

PG&E residential rate schedule

PG&E residential rate schedule

Utility customers, however, don’t need to be stuck with the high rates. There are ways, that they can reduce electricity usage and lower energy cost. Installing  a Power-save 1200 power factor conditioning unit is one of them . The amount of savings for the heavy usage months will help to quickly pay for the few hundred dollar initial investment for the purchase and installation of the unit. It is a cost effective means to save energy and will in the long run pay off through energy savings and lower energy bills.


Money Isn't What (All) You Are Saving

Money Isn't What (All) You Are Saving?

According to a 10/19/2009  New York Times report of an Energy Department internal review, while the Energy Department requires manufacturers of windows and L.E.D. and fluorescent lighting to have independent laboratories evaluate their products, the report said, companies that make refrigerators, washing machines, dishwashers, water heaters and room air-conditioners, which consume far more energy, can certify those appliances themselves.

One refrigerator manufacturer tipped off the Energy Department that some models from a competitor that carried the Energy Star label did not meet the criteria, the audit said. That problem was also described by the Consumer Report magazine in October 2008 about tests it had conducted. In a settlement last year, the manufacturer, LG of South Korea, agreed to modify circuit boards in the machines already sold, to reduce their consumption and to compensate consumers for the extra power consumed.

The report also noted that while the government said in 2007 that it would conduct “retail assessments” to ensure that all the products carrying the Energy Star logo deserved them, it is still not doing so for windows, doors, skylights, water heaters and solid-state lighting. And the department is not following through to ensure that when inappropriately labeled products are identified, the labels are actually taken off, the audit said.

Meanwhile, if you are planning to replace your appliances with Energy Star labeled products, you might also consider installing a Power-save Power Factor Conditioning Unit to ensure that you save energy and lower your electric bills.

Power-Save 1200

Power-Save 1200

One of the most frequently asked questions is how do I know if the power factor conditioning unit Power-save 1200 will work in my home, save electricity, and lower energy cost? Yes, it will work as long as you have an empty slot in your circuit breaker panel that has breaker switches and not the old screw in type fuses. The unit will work on any single-phase electric application for homes. And if your answer is “yes” to only two of the following questions then you could be saving a significant amount of money on your electric bills!

Is your home over 2500 Square feet?

Is your central air conditioner / heat pump unit 3 years or older?

Is your forced air furnace 3 years or older?

Do you have a pool?

Do you have a well?

Do you use an air conditioner?

Is your refrigerator / freezer not EnergyStar rated?

Do you have more than one refrigerator / freezer?

Is your washer / dryer not EnergyStar rated?

Do you have a hot tub or a jacuzzi?

Is your dishwasher not EnergyStar rated?

Do you have a number of appliances in your home?

Three Phase Power Factor Conditioning

Tuesday, October 6, 2009
posted by livinggreen

Single phase power supply is used in most U.S. residential service. The split phase is used to power larger loads that are too large to run off 120V. Otherwise, 120V single phase is used. Most US consumer appliances are single phase, so there is rarely a need to run 3 phase power supply into homes. For most household use the Power-save 1200 single phase Power Factor Conditioning Unit will suffice.

power-save-3200

Power-save 3200/3400

A three phase power supply is used mainly in industrial settings with heavy equipment or motorized tools. Unlike residential service which is always 120/240V, industrial 3 phase can be much higher, with 480V not uncommon. The designer of the building is expected to design the electrical system for the use of the building. It is not uncommon for these buildings to have their own step-down transformer to 120/208V for lower voltage loads. For these applications, we recommend the three phase power factor conditioning units. The  Power-save 3200 is for inductive loads up to 200 amp. and motors up to 75 horsepowers (hp) and the  Power-save  3400 is for inductive loads up to 400 amp. and motors from 75 hp to 300 hp.

For those who are  technically inclined, a more detailed explanation of three phase electrical power can be found  here :-   http://en.wikipedia.org/wiki/Three-phase_electric_power

In case you still have doubt about the effectiveness of the power factor conditioning unit as an energy saving device for lowering your electric bill, here is an actually example of the savings a customer in Texas sees a month after installation of the Power-save 1200 power factor conditioning unit.

Sample Residential Electric Bill Showing Saving Post Installation

Sample Residential Electric Bill Showing Saving Post Installation

Notice the kWh usage difference between October 2008 (the dark bar) and that of October a year earlier. This is further reflected in the average kWh per day as seen in the lower table —- a difference between 37.3 and 66.3 a year earlier. That is an amazing 47% saving. While results may vary, users of Power-save 1200 across the country have consistently been reporting significant energy savings, as well as lowering  electric bills. The power factor conditioning unit is definitely an energy saving product for every household to consider.  Rarely will you find an $300 investment that will provide you a return of this magnitude every month.

At a time of shrinking state and federal dollars for education, Frederick County Public Schools recently installed the Power-Save 1200 Power Factor Conditioning Unit in an unsolicited test of the effectiveness of the unit. Instead of cutting funds for educational programs, the school district is trying to save money by lowering their electicity bill.

“I’ll be conservative, if we can save 10%, that is $650,000 a year we could save,” says Charlie Dalphon, the energy manager. For more detail, please watch this recent  NBC news broadcast.

Power Factor Conditioning Unit

Saturday, October 3, 2009
posted by livinggreen

For a long time, electricity in this country costs only pennies a kilowatt-hour (kWh). That is no longer the case. In recent years, communities across America have seen their electric rates rising steadily. Most households now pay anywhere from 8-20 cents a kWh. In Philadelphia, we are paying over 16 cents per kWh. In places like New York, it is over 20 cents per kWh, and in Hawaii well over 30 cents. This upward trend will likely continue in the foreseeable future.
One way to minimize the impact of rising utility cost is to install energy saving devices. One such device is the Power-save 1200. Installing a Power-save 1200 Power Factor Conditioning Unit will help you improve energy efficiency in your home, and lower your energy cost.
Power-save 1200 Power Conditioning Unit
Inductive loads such as electric motors, pumps and compressors kick back unusable energy into the power system. This unusable energy is turned into heat build-up in appliances, noise on transistor radios and cordless phones, etc. The power factor conditioning unit has capacitors that capture unusable energy drawn from the power-line, and re-channel it back to your appliances, thus reducing waste and increasing energy efficiency of your household appliances. In actual field tests, this power factor conditioning unit has consistently shown power savings of as much as 25%. The unit also provides 2000 joules of whole house surge protection, thus further protecting your expensive home appliances and equipments from damage due to electrical surges. Among energy saving products, the power factor conditioning units are definitely a cost effective investment.